Company news

Home>News > Company news

How to install CO2 laser engraving and cutting machine correctly from ZS laser

ZiShuo laser technology Co., Ltd

How to install CO2 laser engraving and cutting machine correctly? This is really an important question, because only when you install the machine correctly, you can use it correctly. Do not worry, because the video will help to show you the process of how to correctly install a CO2 laser engraving and cutting machine.

Step 1 :
Remove all the package recover the machine like the wood , plastic film and so on (be careful of the nails ) 

Step 2 :
Open the front door ,side-door and get all the extra parts of the machine out ,like : water chiller/water-pump , dust collector , air pump ,laser tube ,Softdog ,Rotary etc.

After you open the front door ,please cut the tie on the belt of the X-axis and Y-axi, get the CD , then move the laser head to the center of the working area by your hand.

Step 3 :
The most important step to correctly install a CO2 laser engraving and cutting machine is to install the CO2 laser tube. So, pay special attention here.

1. Take the laser tube out of the package slowly , then put it on the laser tube socket at the back of the machine.
2. There are two ends of the laser tube. One is laser light out and the other is high pressure end . 
3. If the laser tube has the plastic protective sleeve , please cover the protective tape. If not , please cover sufficient waterproof tape . On the laser light out is the water out , behind the high pressure end is the water in . The theory is “ low in high out ”.

Step 4 :
The installation of the water chiller / water pump:
1.Water chiller: connect the water inlet and water outlet of water chiller with the water outlet and water inlet of the machine by the Silicone tube ,then connect the air plugs ALARM OUTLET (water protective )
2. Water pump : connect the silicone tube with the water outlet of the water pump with the water inlet of the laser machine . Then use the other silicone tube connect the water outlet of the machine with the bucke.

Step 5 :
The installation of the air pump: 
Connect the air outlet of the air pump with the air inlet of the laser machine . (Air inlet )

Step 6 :
The installation method of the dust collector :
Connect the exhaust port of the dust collector with the telescopic pipe of the laser machine .

Step 7 :
The installation of the Ground :
Connect the ground security , find a wire (above one square metre),and should connect the machine to the ground .the other end connect the steel bar, it must be buried under the ground 1.5 metre. If in the wet place , the bury depth can be shallow.

You should check wether all parts of the laser machine are installed correctly and wether the electrical accessories and line are dropped or damaged.

This is aslo significant to correctly install CO2 laser engraving and cutting machine. 

Step 8 :
Our laser machine should use the power with the 220v. If you local power is 220 v , you can connect it directly. If not , you need an extra power transformer for the machine to the change the power. 

Step 9: 
First
supply the power to the water chiller . Then check the silicone tube to see whether it can make water , special whether the water flow is normal . 

Step 10 : 
Connect the power : connect the 220v power to the laser power and open the urgent stop, thenthe power locks in order to see whether the power is normal . Press ESC twice ,then press the up-down-right-left on the Leetro control panel to see whether the laser head can move normally .

Step 11 : 
Plug the softdog in the computer , copy the data of the CD to the computer ,use the blue data cable to connect the computer with the leetro card , then install the software correctly. 

Step 12 : 
Open the Lasercut icon on the computer desktop , and design a circle about 40*40 mm , the processing method is ( cutting ), speed is ( 100 ),power is ( 1 ),then download to the machine. Move the laser head to the proper place then press “test” to see whether the laser head can go around the border. If it is normal ,press “start” and begin work .

By now, The video of how to correctly install CO2 laser engraving cutting machine has ended. Hope this video can help to remove your confusion about the installation of a CO2 laser machine. If you sill have any question , please feel free to contact with us. We will try our best to help you. 

More information about this, please visit our official website: www.zslasertech.com

or contact us directly by email : andy@zslasertech.com


Please feel free to give your inquiry in the form below.
* Subject :
* Email :
  • Name :

  • Phone:

  • *Message :
    Message